|
MATERIAL SAFETY
DATA SHEET |
| 1. IDENTIFICATION OF
THE SUBSTANCE/PREPARATION AND OF THE COMPANY |
| Product Name: |
MiteX |
| Application: |
Desiccant insecticide
for agriculture |
| Company: |
Agil Ltd. |
| Address: |
Hercules 2, Calleva Park, Aldermaston,
Reading, RG7 8DN. |
| Country: |
United Kingdom. |
| Tel/Fax No's: |
| Tel: + 44 (0) 118
981 3333 |
Fax: |
+ 44 (0) 118 981
0909 |
| Emergency Number:
out of hours- |
|
+ 44 (0) 118 926
5589 |
| |
|
+ 44 (0) 118 947
4407 |
|
|
| 2. COMPOSITION/INFORMATION
ON INGREDIENTS |
Substance: Kieselgur ~
Purified silicate mineral (E 551c)
CAS Number: 61790-53-2
|
| 3. HAZARDS IDENTIFICATION |
None.
However, MiteX
does contain free silicates. Ensure that
atmospheric dust levels are
maintained such that the amount of respirable
silicates in the atmosphere is <0.4
mg/M3. Long-term exposure to excessive
levels of any mineral dust can lead to
respiratory problems.
|
| 4. FIRST AID MEASURES |
| Eye contact: In
case of contact with eyes, rinse immediately
with
plenty of water
Inhalation: If strong inhalation of dust
occurs it is recommended to clear the
airways
|
| 5. FIRE FIGHTING MEASURES |
| Non-Flammable
|
| 6. ACCIDENTAL RELEASE MEASURES |
Personal
precautions: Wastes are not classified as hazardous
Environmental precautions: None
|
| 7. HANDLING AND STORAGE |
| Handling: |
Common
care and ensure low dust levels. |
| Storage: |
Store
in clean dry conditions. Keep container
closed and
ensure label is intact and legible |
|
| 8. EXPOSURE/PERSONAL CONTROL |
| Engineering
Measures: |
N/A |
| Control
Parameters: |
None |
| Personal
protection equipment: |
|
|
| |
At high dust
levels and/or workers suffer from
dermatitis or sensitive skin
S36 Wear suitable protective clothing |
|
| 9. PHYSICAL AND CHEMICAL PROPERTIES |
| Appearance: |
Beige
/ Grey powder |
| Odour: |
None |
| pH |
~ pH 4.5 |
| Boiling
point: |
N/A |
| Melting
point: |
>1000oC |
| Flash
point: |
N/A |
| Explosive
properties: |
Non-explosive |
| Vapour
pressure: |
N/A |
| Relative
density: |
325 g/l |
| Solubility: |
Generally
insoluble in common solvents |
|
| 10. STABILITY AND REACTIVITY |
| MiteX
is chemically inert to all fluids with
the exception of hydrofluoric acid.
Conditions
to avoid: None
Materials to avoid: Hydrofluoric acid
|
| 11. TOXICOLOGICAL INFORMATION |
Non-toxic.
Excessive exposure to dust may affect susceptible
persons as follows:
Skin contact: Mild irritation
Eye contact: Mild irritation
|
| 12. ECOLOGICAL INFORMATION |
MiteX
is an environmentally compatible material.
|
| 13. DISPOSAL INFORMATION |
Disposal
Considerations
Disposal
must be in accordance with local and
national
legislation.
Dispose
of through an authorised waste contractor
to a
licensed site.
Provided
care is taken to inhibit airborne dust,
normal factory
disposal procedures may be employed
using skips and tips,
then landfill. Spillages may be swept
up. The use of water is
not recommended; surfaces coated
with wet material would
be a slipping hazard.
|
| 14. TRANSPORT INFORMATION |
No special precautions,
other than dry conditions, are
necessary.
|
| 15. REGULATORY INFORMATION |
| LABEL
FOR SUPPLY: |
| |
NONE |
| RISK PHRASES: |
None.
However, workers should be informed
of the presence
of crystalline silica and be trained
in the proper use and
handling of this product as required
under applicable
regulations.
|
| SAFETY PHRASES: |
S22 Do not breathe
dust
S26 In case of contact with eyes, rinse
immediately with
plenty of water
S36 Wear suitable protective clothing
(susceptible
persons and in dusty conditions)
|
STATUTORY INSTRUMENTS:
|
Health and Safety at
Work Act 1974.
Chemicals (Hazard Information and Packaging
for supply)
Regulations 1994.
Control of Substances Hazardous to Health
Regs 1988 (Si
1657).
Environmental Protection Act 1990.
|
| CODES OF PRACTICE: |
Waste management: The
duty of care. |
| GUIDANCE NOTES: |
Health and Safety Executive:-
Occupational exposure limits (EH
40/94)
Classification, Packaging and Labelling of Dangerous
Substances Regulations 1984
|
|
| 16. OTHER INFORMATION
|
Recommendations/restrictions:
It is
important to follow the instructions detailed
in the Product Data Sheet. If this product
is for resale, ensure that the purchaser
receives a copy of this information. The
information herein is believed to be correct
as of the date hereof but is provided without
warranty of any kind. The recipient of
our product is responsible for ensuring
that, where applicable, existing laws and
guidelines are observed.
|
